+39 0331 1693557
inti@intisrl.it
Download of all our available used machinery
Rudolf Deckert filler MFM - 104 in line with Emerson micro flow flow meter dosing system.
4 filling stations with 4 pneumatic needles.
Product accumulation vessel.
Adjustable dosage from panel.
The monoblock F87 is an automatic intermittent movement machine that can perform three operations at the same time: a volumetric filling and two closures. Aqueous, alcoholic, sugary, foamy, viscous products can be given. Droppers, glass or plastic pipettes, nebulizers, normal or freeze-drying rubber caps can be introduced. You can apply screw caps, press caps, ferrules, PFP etc. The carter and the machine table, on which all the operating groups are fixed from the inside, are in AISI 304 stainless steel and protect the mechanical parts from the infiltration of the treated products and the water used for washing. The operating units and their supports are made of AISI 304 stainless steel and receive their motion from a single variator motor, obtaining the dual purpose of relating, without interruption, the speed of the machine with the rotation speed of the screwing or seaming, and not to have electric motors above the work stations, thus eliminating sources of possible pollution of the treated products. The volumetric filling unit is also located on the machine - plane and the syringes (in glass or stainless steel) act vertically. This solution avoids the radial stresses that are often the cause of breakages, reduces wear, and facilitates the adjustment and cleaning of the filling units. The closing groups are designed to process all types of caps or caps commonly used in the chemical, pharmaceutical and cosmetic industries and have simple and easy adjustments that reduce time for format change. A peculiar feature of the group for the introduction of caps or droppers is the ability to rotate the closing element during the introduction phase. The advantages of this system are manifested especially with soft rubber stoppers which, if introduced without rotation, tend to come out of the bottle. The screwing of the capsules takes place in two stages: a spindle picks up the capsule, brings it to the bottle in the correct position and gently pre-screws it. At the next station, a screwdriver tightens it respecting the desired tightening torque. The vibrating feeders of the closing elements are positioned at about 1200 mm from the floor, so the operator has no difficulty in checking and supplying them.
Bottle filling & closing machine Monoblock
For bottles and vials, format: from 25mm to 270 mm
Pumps: 4 units installed
Operational hours counter: 7054h
Semi-automatic filling machine for liquids and dense products - Volumetric doser with floor base, ideal for the operator who has to work standing. Suitable for food / chemical / cosmetic
The hopper is located at a height of approximately 2 m from the ground.
TECHNICAL CHARACTERISTICS : 40 kg - 20-700 cc
Manufacturer: Lieder
Year of manufacture: 1991
Model : TA 51
Description : Filling and sealing machine Lieder TA 51
Technical features: Full volume 30 ml - 260 ml Functions: Filling and sealing of jars Speed : up to 50 jars per minute
Automatic intermittent motion machine, suitable to fill bottles with liquid.
Nozzle movement performing fractional filling of the total volume.
One or two intermittent motion Plugging/Capping groups.
The ML640 model is specific for capping operation only.
Main Features:
Stainless steel covered frame.
Separation between the bottle transport and mechanical area.
Machine main drive unit with electronic speed variation.
FLEX-LINK tabletop conveyor for bottle infeed and discharge with stainless steel adjustable guides.
Independent servo driven units with speed adjustment from Display.
Carousel with 15 pockets to transport and place the bottles under the filling/closing heads.
DOSING RANGE With stainless steel syringes: 1 - 500 ml With ceramic syringes: 1 - 300 ml CONTAINER SIZE Ø of round bottle: 18 - 90 mm Width x Width, square bottle: 20 - 80 mm Long side, rectangular bottle: 20 - 85 mm Short side, rectangular bottle: 20 - 60 mm Tot. height, without closure: 35 - 180 mm OUTPUT Production speed: Up to 75 Cycles/Min.
Filling and capping monoblock Ima mod. F57:
The F 57 model was designed and built according to G.M.P.
Their work groups and their placement on the work base allow for easy, safe and fast cleaning and washing. It is an automatic machine with alternating movements which in the standard version can perform 3 operations: one for volumetric filling and two for closing. Water-based products can be dispensed. alcoholic, sugary and viscous.
The compact line turns out to be quite functional and practical.
The base of the machine, on which all the operating groups are fixed from the inside, are made of AISI 304 and protect the mechanical parts from leaks from the products used and from the water used for washing.
The work groups and the relative supports are built in AISI 304 and receive the movement of a single variable speed motor. Thanks to this, it is possible to avoid having electric motors in the upper part of the work area, avoiding any possibility of contamination of the products on which to work.
Technical specifications :
Production: 80 bottles per minute mechanical output
Bottle diameter: 14–80 mm
Bottle height: 35–180 mm
Cap diameter: ---- / 55mm max
Cap Height: ---- / 65mm max
Filling range: 5 - 500 ml (depends on the pistons it is equipped with)
The F400S is a closing filling machine designed to perform in-line filling and capping operations for aseptic glass bottles. The machine consists of the following units: bottle infeed conveyor, screw conveyor unit, filling carousel, capping carousel, bottle outfeed and rejection carousel, syringe unit, chasing nozzle head, transfer carousel, vibrating cap sorter, bottle rejection conveyor, bottle outfeed carousel, transfer carousel, post-fill gassing tunnel, laminar flow, sampling belt, pre-corking gassing tunnel, bottle stop piston.
SECTOR OF USE:
Pharmaceutical, chemical, cosmetic, food, dietary, medical devices, manufacturing.
PECULIARITY:
The bottles are brought to the first conveyor star by the incoming conveyor belt, passing by an auger that has the function of putting the bottles in phase with the carrousel itself, then they are passed to the second transfer star and given to the filling carrousel. The full bottle is then passed to the capping carrousel. At the end of the operation, the finished product is passed from the exit carrousel to the exit or rejection belt.
The various operational phases are briefly divided into:
-conveyance of incoming bottles,
-filling bottles,
-tapping bottles,
-flowing bottles,
-discarding non-compliant bottles or sampling.
Last format processed: 100 ml glass bottle, cap diameter 30.9 mm, flip-off ring diameter 37.0 mm.
The filling machine is complete with rotary table, LAF filtration hood system, 100 ml format and modular transmitter brand Mettler Toledo model M700 which with ISM technology allows perfect integration of sensor diagnostics.
Year of construction: 2006
TECHNICAL SPECIFICATIONS Length mm 5000 Width mm 2300 Height mm 2050 Weight Kg 3500 Power kW 17 Frequency Hz 50 Voltage Volt 400 Max. output Bottles/min 400
Via XXV Aprile, 8
21054 Fagnano Olona (VA)
Italia
Tel. +39 0331 1693557
email: inti@intisrl.it
